1000A 30V IGBT Rectifier For For Electroplating

1000A30V IGBT Rectifier for for Electroplating AIR COOLING

Product Details

Application

30V 1000A High Frequency Switching Electroplating Rectifier with IGBT,IGBT Based Rectifier for Plating , DC Power Supplies For Plating.

imageimage


Technical Requirement

GA-1000A/30V-STA-S

1End of cycle timer and ampere time has time selectable in seconds, minutes and hours.

1Set for a pre-determined count and shut off similar to a cycle timer

1be able to reach 30V +/- 1V

1Ramp controlled rectifiers with voltage/current regulation shall have an adjustable current ramp regulator with a zero to maximum rise time between 1 and 3 seconds Minimum output of 30 +/- 1 V done within 1-3 seconds . Ramp time should be adjustable. However the user can adjust the ramp time up to 90 seconds if necessary.

1Adjustable ramp – This should be linear in both Current Control and Voltage Control – Scale can be adjustable by the user and can be changed from the HMI. AND this can be stepped up manually from the HMI by the user.Adjustable linear current or voltage ramp to preset value. Time adjust selection needs to be in seconds, minutes, and hours.

1≤5 % output ripple as a standard,5.2 V maximum peak to peak ripple AND 5.2 V spike maximum at 30V,This is very important

1Optional air filters for harsh environments

1Input front end disconnect. Add 3 phase contactor on the input to disconnect unit from incoming lines during fault conditions to isolate the unit. After the fault has been cleared the unit can either start automatically or manually depending on user preference by closing the contactor.

1 Ammeter to have half digit.  Example 100.3A


1 Recipes. At least 10 individual recipes in each power supply as a standard. These should be application configurable and storable. Include password protect option.Each recipe will have user set points of voltage or current, ramp and option of stop on elapsed time or ampere time.


Video of  1000A30V Rectifier 


image


Technical Data 

1. AC Input

1.1

Input AC phase

3 phase 

1.2

Input AC line nos.

A,B,C,G  

1.3

Input line voltage(V)

  480V

1.4

Input Frequency(Hz)

60Hz

2. DC Output

2.1

Rated Output

DC 30V +/-1V 1000A 

2.2

Output mode and range

Constant Current, 0-100% of rated value

Constant Voltage, 0-100% of rated value

2.3

Duty

100% full load

2.4

Accuracy

<1%

3. Electrical Features

3.1

Application

Electroplating 

3.2

Regulation mode

IGBT PWM

3.3

Cooling Method

Forced air cooling 

34

Remote control interface

RS485 MODBUS RTU  

3.5

Power Factor(Full load)

0.93

3.6

Touch panel HMI

RYes   £No

3.7

IP degree

IP30  

3.8

Insulation Grade

B

3.9

Working Mode

Continuous

3.10

Alarm type

Audible and visual alarm(on DC power supply front panel and touch panel)

3.11

Voltage/current ripple

≤5(In the normal working range, the output current ripple)

19Warranty 

Green Power provides a warranty as stated in the order acknowledgment or contract. The warranty covers defects in design, materials and manufacturing. Defects that can be shown to have arisen as a consequence of incorrect use and/or maintenance are not covered. If fault of DC power supply happens during the warranty period, Green Power technology must be contacted before any work is undertaken on the DC power supply

Hot Tags: 1000A 30V IGBT Rectifier For For Electroplating China, India, manufacturers, factory, customized, high quality, price

Send Inquiry

You Might Also Like